ITEQ IT-170GRA2 PCB: Stack-up-design och signalförlusttestning

IT-170GRA2 high-speed low-loss PCB banner with two green board layouts

Illustration of high-speed PCB layouts.

ITEQ IT-170GRA2 is a halogen-free, high-Tg epoxy laminate and prepreg for lower-loss multilayer PCBs. ITEQ reports a dielectric constant (Dk) of 3.8 and a dissipation factor (Df) of 0.0080 at 10 GHz on a 50% resin-content specimen. That is a useful starting point for selecting a server, storage, networking or backplane stack-up. The decision to use it belongs to the channel loss budget.

Give the PCB its share of the channel loss budget

Start with a frequency-dependent limit and define the electrical reference planes. If the limit is specified from transmitter package to receiver package, reserve margin for the packages, connectors, launches, via transitions and fabrication variation before assigning the remaining loss to routed board traces. For a simple NRZ link, half the bit rate is the Nyquist frequency; for a multilevel link, use the symbol rate and the applicable specification. A single Nyquist checkpoint is useful for screening, but a production mask may cover a band and include return loss, crosstalk or mode conversion as separate requirements.

A first-pass loss allocation can add estimated positive loss contributions in decibels when the sections are well matched. Then cascade the actual transition and line models or measure the representative channel. Reflections can make the insertion-loss curve ripple, so the arithmetic budget is not a substitute for the cascaded result. Decide early which transitions belong to the board supplier’s test and which must wait until connectors or components are populated.

Compare the longest routed layer segments first. Where the dominant loss is in a long uniform trace, a lower-Df construction and a suitable foil may buy more margin. A short path with a deep plated via stub or a poorly referenced connector launch may benefit more from a layout change. In that second case, putting IT-170GRA2 into the same artwork may leave the main loss mechanism in place.

IT-170GRA2 Dk and Df by frequency

Använda IT-170GRA2TC as the laminate designation and IT-170GRA2BS as the prepreg designation when reconciling the drawing with ITEQ’s data. ITEQ lists Tg as 175°C by DSC and 170°C by TMA. Neither value replaces component and solder-paste limits for assembly.

IT-170GRA2 typical electrical data at 50% resin content
Frekvens Dk Df IPC-TM-650 method
1 GHz 4.0 0.0060 2.5.5.9
2 GHz 3.9 0.0063 2.5.5.13
5 GHz 3.9 0.0075 2.5.5.13
10 GHz 3.8 0.0080 2.5.5.13

Källa: ITEQ IT-170GRA2 datasheet, Rev. 1.0-26. The frequency points report test results; the table does not define a frequency limit for a product or a guaranteed loss per unit length.

How does it compare with IT-170GT? ITEQ reports 0.0095 Df at 10 GHz and 55% resin content for IT-170GT. The listed values point toward IT-170GRA2 when dielectric loss is the primary concern. They come from different resin contents, so applying the percentage difference directly to a finished channel would be misleading. Recalculate impedance and insertion loss for the proposed glass, pressed thickness and foil before approving a substitution.

IT-170GRA2 PCB illustration with two boards and dense routing

High-speed routing illustration. Evaluate channel loss on the specified stack-up and transitions.

Control the fabrication variables in the field model

Specify the copper surface that faces the dielectric

The smoothness of a foil label alone does not define conductor loss. The bonding treatment and roughness on the relevant copper surface change the current path when skin effect becomes significant. ITEQ’s sheet reports peel strength for a 35 µm low-profile foil reference; peel strength cannot be converted to the roughness parameters needed by a channel solver. Freeze the foil designation and treatment for the signal layer and its reference as applicable, and request roughness information compatible with the solver model. A change in PCB-koppars ojämnhet can move the loss curve while an impedance coupon still passes.

Keep the line and the discontinuities in the same release

Give CAM an impedance table by layer and reference plane, with finished copper thickness, pressed dielectric, differential gap and allowed artwork adjustments. The etched trace is often trapezoidal; the top and bottom widths need not match the artwork or each other. When there is kontrollerad impedans, a coupon should reproduce the relevant trace geometry and build. A long differential path can also see skew from local glass weave and routing orientation even when the average Dk and impedance look acceptable.

At the layer transition, evaluate the return-path change and the unused via barrel. A poorly placed return via or plane opening changes the transition; a stub can create a frequency-selective notch. Where bakborrning is contemplated, state the signal layer that must be protected, permissible residual stub and depth reference. Check these against both electrical sensitivity and the drill-depth tolerances agreed for the board.

PCB-TILLVERKNING OCH MONTERING

Planning an IT-170GRA2 PCB build?

Highleap kan tillsammans granska kraven för brädans konstruktion och montering.

Include the target impedance, channel loss budget, reference test frequencies and any specified foil.

Begär en granskning av tillverkning och montering

Measure uniform trace loss separately from launches

Use TDR to locate impedance changes and confirm the line impedance profile. Use a calibrated VNA and an agreed S-parameter measurement to check insertion loss. For a differential line that may be mixed-mode Sdd21; agree on port mapping, normalization, calibration, de-embedding and the reference planes. Differences in launch layout or fixture handling can consume a significant fraction of a short coupon’s measured loss.

Hypothetical coupon calculation. At 10 GHz, a 50 mm trace coupon shows 1.4 dB of positive insertion loss and a 150 mm coupon shows 3.0 dB. With otherwise identical launches and matched uniform lines, the difference suggests about 1.6 dB per 100 mm for that construction at that frequency. Mismatches and fixture asymmetry can invalidate a simple subtraction, so compare the full traces and use the agreed extraction method. These values illustrate the calculation and do not describe an IT-170GRA2 test.

A line-loss coupon includes dielectric and conductor effects together. It does not isolate the resin’s Df, cover every routed layer or reproduce connector and via transitions unless those structures are deliberately included. For a failing first article, use time-domain localization and frequency-domain data together: broad excess attenuation along a uniform length points toward geometry or losses in the construction; a localized reflection or notch calls for checking the launch, return path or via. Neither symptom alone identifies a root cause.

Specify the bare-board and populated tests at quotation

Send the proposed stack-up, routed layer lengths, loss mask, impedance targets, foil requirements, coupon drawings and the electrical reference planes with your Highleap PCB fabrication and assembly inquiry. If the final channel includes populated connectors, add their part numbers, footprints, assembly requirements and any final-fixture definition. Highleap Electronics can review the fabrication inputs, quote assembly against the approved BOM and clarify which measurements belong at first article, at board release or after assembly. Confirm material availability and the measurement scope for the actual build before the design is frozen.

Helen Chong

Om författaren

Helen Chong

Konsult inom kretskortslösningar och chef för affärsutveckling utomlands på Highleap Electronics

Helen stöder internationella ingenjörsteam med kompletta lösningar för tillverkning och montering av kretskort, och hjälper projekt att gå från snabba prototyper till stabil massproduktion. Hennes erfarenhet omfattar högfrekvens- och RF-kort, komplexa flerskiktsuppbyggnader, rigid-flex och flex PCB-teknik inom flera branscher.

Genom att översätta tekniska krav till praktiska tillverkningsplaner hjälper hon kunder att förbättra tillverkningsbarheten, minska risker och optimera kostnader och ledtider – samtidigt som hon bibehåller en jämn kvalitet i stor skala.

Highleap PCB- och PCBA-lösningar - begär offert

Rekommenderade inlägg

Hur man får en offert för kretskort

Låt oss köra en DFM/DFA-analys åt dig och återkomma till dig med en rapport. Du kan ladda upp dina filer säkert via vår webbplats. Vi behöver följande information för att kunna ge dig en offert:

    • Gerber, ODB++ eller .pcb, spec.
    • Stycklista om du behöver montering
    • Antal
    • Vändningstid

Förutom kretskortstillverkning erbjuder vi ett omfattande utbud av elektroniska tjänster, inklusive kretskortsdesign, PCBA och nyckelfärdiga lösningar. Oavsett om du behöver hjälp med prototypframtagning, designverifiering, komponentförsörjning eller massproduktion, erbjuder vi heltäckande support för att säkerställa ditt projekts framgång.

För PCBA-tjänster, vänligen ange din BOM (Bill of Materials) och eventuella specifika monteringsanvisningar. Vi erbjuder även DFM/DFA-analys för att optimera dina konstruktioner för tillverkningsbarhet och montering, vilket säkerställer en smidig produktionsprocess.

    Berätta om ditt PCB-projekt

    Inga designfiler än? Inga problem. Dela med dig av din kunskap så återkommer vi om mer information behövs.



    Ladda upp filer (Tillval)

    PCB-filer, BOM, PDF/STEP, TXT, bilder, ZIP/RAR/7Z · Max 50 MB totalt