ITEQ IT-170GRA2 PCB: Katman Yapısı Tasarımı ve Sinyal Kaybı Testi

IT-170GRA2 high-speed low-loss PCB banner with two green board layouts

Illustration of high-speed PCB layouts.

ITEQ IT-170GRA2 is a halogen-free, high-Tg epoxy laminate and prepreg for lower-loss multilayer PCBs. ITEQ reports a dielectric constant (Dk) of 3.8 and a dissipation factor (Df) of 0.0080 at 10 GHz on a 50% resin-content specimen. That is a useful starting point for selecting a server, storage, networking or backplane stack-up. The decision to use it belongs to the channel loss budget.

Give the PCB its share of the channel loss budget

Start with a frequency-dependent limit and define the electrical reference planes. If the limit is specified from transmitter package to receiver package, reserve margin for the packages, connectors, launches, via transitions and fabrication variation before assigning the remaining loss to routed board traces. For a simple NRZ link, half the bit rate is the Nyquist frequency; for a multilevel link, use the symbol rate and the applicable specification. A single Nyquist checkpoint is useful for screening, but a production mask may cover a band and include return loss, crosstalk or mode conversion as separate requirements.

A first-pass loss allocation can add estimated positive loss contributions in decibels when the sections are well matched. Then cascade the actual transition and line models or measure the representative channel. Reflections can make the insertion-loss curve ripple, so the arithmetic budget is not a substitute for the cascaded result. Decide early which transitions belong to the board supplier’s test and which must wait until connectors or components are populated.

Compare the longest routed layer segments first. Where the dominant loss is in a long uniform trace, a lower-Df construction and a suitable foil may buy more margin. A short path with a deep plated via stub or a poorly referenced connector launch may benefit more from a layout change. In that second case, putting IT-170GRA2 into the same artwork may leave the main loss mechanism in place.

IT-170GRA2 Dk and Df by frequency

Kullanım BT-170GRA2TC as the laminate designation and IT-170GRA2BS as the prepreg designation when reconciling the drawing with ITEQ’s data. ITEQ lists Tg as 175°C by DSC and 170°C by TMA. Neither value replaces component and solder-paste limits for assembly.

IT-170GRA2 typical electrical data at 50% resin content
Sıklık Dk Df IPC-TM-650 method
1 GHz 4.0 0.0060 2.5.5.9
2 GHz 3.9 0.0063 2.5.5.13
5 GHz 3.9 0.0075 2.5.5.13
10 GHz 3.8 0.0080 2.5.5.13

Kaynak: ITEQ IT-170GRA2 datasheet, Rev. 1.0-26. The frequency points report test results; the table does not define a frequency limit for a product or a guaranteed loss per unit length.

How does it compare with IT-170GT? ITEQ reports 0.0095 Df at 10 GHz and 55% resin content for IT-170GT. The listed values point toward IT-170GRA2 when dielectric loss is the primary concern. They come from different resin contents, so applying the percentage difference directly to a finished channel would be misleading. Recalculate impedance and insertion loss for the proposed glass, pressed thickness and foil before approving a substitution.

IT-170GRA2 PCB illustration with two boards and dense routing

High-speed routing illustration. Evaluate channel loss on the specified stack-up and transitions.

Control the fabrication variables in the field model

Specify the copper surface that faces the dielectric

The smoothness of a foil label alone does not define conductor loss. The bonding treatment and roughness on the relevant copper surface change the current path when skin effect becomes significant. ITEQ’s sheet reports peel strength for a 35 µm low-profile foil reference; peel strength cannot be converted to the roughness parameters needed by a channel solver. Freeze the foil designation and treatment for the signal layer and its reference as applicable, and request roughness information compatible with the solver model. A change in PCB bakır pürüzlülüğü can move the loss curve while an impedance coupon still passes.

Keep the line and the discontinuities in the same release

Give CAM an impedance table by layer and reference plane, with finished copper thickness, pressed dielectric, differential gap and allowed artwork adjustments. The etched trace is often trapezoidal; the top and bottom widths need not match the artwork or each other. When there is kontrollü empedans, a coupon should reproduce the relevant trace geometry and build. A long differential path can also see skew from local glass weave and routing orientation even when the average Dk and impedance look acceptable.

At the layer transition, evaluate the return-path change and the unused via barrel. A poorly placed return via or plane opening changes the transition; a stub can create a frequency-selective notch. Where geri delme is contemplated, state the signal layer that must be protected, permissible residual stub and depth reference. Check these against both electrical sensitivity and the drill-depth tolerances agreed for the board.

PCB ÜRETİMİ VE MONTAJI

Planning an IT-170GRA2 PCB build?

Highleap, panonun yapım ve montaj gereksinimlerini birlikte inceleyebilir.

Include the target impedance, channel loss budget, reference test frequencies and any specified foil.

İmalat ve montaj incelemesi talep edin

Measure uniform trace loss separately from launches

Use TDR to locate impedance changes and confirm the line impedance profile. Use a calibrated VNA and an agreed S-parameter measurement to check insertion loss. For a differential line that may be mixed-mode Sdd21; agree on port mapping, normalization, calibration, de-embedding and the reference planes. Differences in launch layout or fixture handling can consume a significant fraction of a short coupon’s measured loss.

Hypothetical coupon calculation. At 10 GHz, a 50 mm trace coupon shows 1.4 dB of positive insertion loss and a 150 mm coupon shows 3.0 dB. With otherwise identical launches and matched uniform lines, the difference suggests about 1.6 dB per 100 mm for that construction at that frequency. Mismatches and fixture asymmetry can invalidate a simple subtraction, so compare the full traces and use the agreed extraction method. These values illustrate the calculation and do not describe an IT-170GRA2 test.

A line-loss coupon includes dielectric and conductor effects together. It does not isolate the resin’s Df, cover every routed layer or reproduce connector and via transitions unless those structures are deliberately included. For a failing first article, use time-domain localization and frequency-domain data together: broad excess attenuation along a uniform length points toward geometry or losses in the construction; a localized reflection or notch calls for checking the launch, return path or via. Neither symptom alone identifies a root cause.

Specify the bare-board and populated tests at quotation

Send the proposed stack-up, routed layer lengths, loss mask, impedance targets, foil requirements, coupon drawings and the electrical reference planes with your Highleap PCB fabrication and assembly inquiry. If the final channel includes populated connectors, add their part numbers, footprints, assembly requirements and any final-fixture definition. Highleap Electronics can review the fabrication inputs, quote assembly against the approved BOM and clarify which measurements belong at first article, at board release or after assembly. Confirm material availability and the measurement scope for the actual build before the design is frozen.

Helen Chong

Yazar Hakkında

Helen Chong

Highleap Electronics'te PCB Çözümleri Danışmanı ve Yurtdışı İş Geliştirme Müdürü

Helen, uluslararası mühendislik ekiplerine uçtan uca PCB üretimi ve montaj çözümleri sunarak projelerin hızlı prototip aşamasından istikrarlı seri üretime geçmesine yardımcı oluyor. Deneyimi, yüksek frekanslı ve RF kartlar, karmaşık çok katmanlı yapılar, rijit-esnek ve esnek PCB teknolojileri dahil olmak üzere birçok sektörde geniş bir yelpazeyi kapsıyor.

Teknik gereksinimleri pratik üretim planlarına dönüştürerek, müşterilerinin üretim kolaylığını artırmalarına, riskleri azaltmalarına, maliyet ve teslim sürelerini optimize etmelerine yardımcı olurken, aynı zamanda büyük ölçekte tutarlı kaliteyi korumalarını sağlar.

Highleap PCB ve PCBA çözümleri - fiyat teklifi isteyin

Önerilen Mesajlar

PCB'ler için fiyat teklifi nasıl alınır

Sizin için DFM/DFA analizini çalıştıralım ve size bir raporla geri dönelim. Dosyalarınızı web sitemiz üzerinden güvenli bir şekilde yükleyebilirsiniz. Size bir teklif verebilmek için aşağıdaki bilgilere ihtiyacımız var:

    • Gerber, ODB++ veya .pcb, spec.
    • Montaj gerekiyorsa BOM listesi
    • Adet
    • Dönüş zamanı

PCB üretiminin yanı sıra PCB tasarımı, PCBA ve anahtar teslimi çözümler de dahil olmak üzere kapsamlı bir elektronik hizmet yelpazesi sunuyoruz. Prototipleme, tasarım doğrulama, bileşen tedariki veya seri üretim konusunda yardıma ihtiyacınız olsun, projenizin başarısını garantilemek için uçtan uca destek sağlıyoruz.

PCBA hizmetleri için lütfen BOM'unuzu (Malzeme Listesi) ve herhangi bir özel montaj talimatını sağlayın. Ayrıca, tasarımlarınızı üretilebilirlik ve montaj için optimize etmek ve sorunsuz bir üretim süreci sağlamak için DFM/DFA analizi de sunuyoruz.

    PCB projeniz hakkında bize bilgi verin.

    Henüz tasarım dosyalarınız yok mu? Sorun değil. Bildiklerinizi paylaşın, daha fazla ayrıntıya ihtiyaç duyulursa sizinle iletişime geçeceğiz.



    Dosyaları yükle (opsiyonel)

    PCB dosyaları, BOM, PDF/STEP, TXT, resimler, ZIP/RAR/7Z · Toplam maksimum 50 MB