IT-601G PCB Manufacturing for Multilayer and HDI Boards

IT-601G PCB banner with three dense layouts and fine-pitch pad fields

Illustration of dense PCB routing for an HDI build.

ITEQ IT-601G is a halogen-free, high-Tg material system for advanced HDI PCBs that need low through-thickness expansion and lower dielectric loss. The grade-specific datasheet reports 1.1% Z-axis expansion from 50°C to 260°C. It also reports a 230°C Tg by DMA and a 210°C Tg by TMA. For stacked microvias, the release decision still depends on the construction and on evidence from the actual interconnect sequence.

Resolve conflicting IT-601G values before simulation

Online material summaries can show 10 GHz Dk and Df as 3.5 and 0.0060 at 50% resin content, or label 230°C as a TMA result. For the model and purchase specification, record the grade, document number, revision, resin content, frequency and method together. The ITEQ IT-601G grade sheet W-CTE-1002-64D, Rev. 1.0-26 describes the following specimen results. Do not reconcile differing sources by averaging their values or by moving Dk and Df from one row to another.

IT-601G material values with the test conditions attached
Propriedade Resultado relatado Method or construction
Dk / Df a 1 GHz 3.5 / 0.0055 Teor de resina de 70%; IPC-TM-650 2.5.5.9
Dk / Df a 10 GHz 3.28 / 0.0064 Teor de resina de 70%; IPC-TM-650 2.5.5.13
Tg 230°C DMA; 210°C TMA IPC-TM-650 2.4.24.4 and 2.4.24, respectively
Expansão do eixo Z 1.1% de 50°C a 260°C IPC-TM-650 2.4.24; espécime laminado
Td / T260 / T288 420°C / >60 min / >60 min Td at 5% mass loss; T-times measured separately

Uso TI-601GTC e IT-601GBS to identify the copper-clad laminate and prepreg in the material record. For an impedance or loss model, ask for construction-specific inputs for the actual glass style, pressed dielectric and copper foil. Keep the model and coupon on that same revision. A 70% resin-content datasheet value can be valid and still be the wrong input for a layer with a different construction.

Plan evidence before each lamination hides an interface

IT-601G’s reported Z-axis expansion is useful for screening where temperature excursions load the vertical interconnects. In a stacked via column, however, each copper connection depends on its own geometry, target preparation and plating. A low-expansion laminate does not prevent a weak interface from opening. A staggered transition trades routing area for the ability to avoid placing the next via directly on the previous filled via. Check whether the package can escape with that arrangement before committing to a stacked column.

Hypothetical 2+N+2 process review. In this example two build-up layers are added symmetrically on either side of a central multilayer structure. Some signals pass through a buried via in the center, then through two laser microvias on one side. The checkpoints below describe what to agree for this example; they are neither a claim about a Highleap production line nor a universal process traveler.

Inspection plan for a hypothetical 2+N+2 stack
Estágio de construção Risk to close Evidence to define with the fabricator
Central subassembly Buried-hole barrel or land defects become hard to isolate after build-up. Register the inner layers and define representative checks of buried span, plating and any required fill before it is covered.
First build-up pair Poor contact to the target, incomplete fill or a recessed fill surface under the next via. Agree on local pressed thickness, pad capture, fill profile and planarity inspection at sites that represent the next landing.
Second build-up pair Misregistration or weak copper interfaces within the stacked path. Section representative stack geometry and define a continuity coupon with each interface included in the measured path.
Qualification and release Intermittent opens during temperature excursions; integration errors at fine-pitch lands. Agree on thermal exposure and resistance monitoring, board net test, and finished land/assembly inspection as distinct requirements.

An electrical coupon that bypasses the longest or most demanding stack answers the wrong question. Retain the panel or coupon identity through stress and sectioning so failed locations can be compared to geometry. A section at ambient temperature can look acceptable at the sampled plane even when an interface opens only while hot. For laminação sequencial, decide which observations need to occur during fabrication and which can be made on the completed structure. The IPC-TM-650 method index provides test references; use the method, conditioning and limits specified for the actual program.

IT-601G PCB illustration with overlapping boards and fine-pitch land patterns

HDI PCB illustration. Artwork does not establish the buried interconnect construction or reliability.

Put copper foil changes under revision control

The ITEQ sheet lists 18 µm RTF and RTF2 low-profile foils and 18 µm HTE standard-profile foil with separate peel-strength results. Those are not roughness specifications. Two foil constructions at the same thickness can differ in adhesion treatment and conductor loss. For loss-sensitive layers, specify the permitted foil and the surface information required by the model. Keep the test coupon on the same layer construction as the routed traces.

A foil or prepreg substitution can change more than one result. The new bonding package can change the final dielectric spacing and laser depth, while a new foil treatment can change electrical loss without a large change in TDR impedance. Record proposed substitutions against four items: the pressed thickness, landing and fill geometry, impedance and loss inputs, and the qualification evidence. If any has changed, identify which requirement needs to be demonstrated again. This connects controle de impedância with the process route instead of treating the two as independent drawing approvals.

FABRICAÇÃO E MONTAGEM DE PCBs

Planning an IT-601G PCB build?

A Highleap pode analisar em conjunto os requisitos de construção e montagem da placa.

Include the via map, lamination sequence and the qualification requirements for buried interfaces.

Solicite uma revisão de fabricação e montagem.

Release the HDI stack and the assembly together

Memory, SiP and other compact devices can force via-in-pad and place limits on board and package coplanarity. Agree on pad finish and solder-mask registration, and verify that the released drawings address via fill, cap and flatness where solder joints sit above vias. Include panel handling in the assembly review. X-ray can aid hidden solder-joint inspection; bare-board coupons and sections remain necessary when the acceptance plan requires evidence of buried interconnect integrity.

Para um IT-601G fabrication and PCBA estimate, provide the controlled material revision, core and prepreg constructions, via span and stack maps, foil and electrical inputs, and coupon acceptance requirements. Pair those files with the package footprints, BOM, placement file and assembly drawing. Highleap Electronics can then review material sourcing, the build-up sequence, and the first-article inspection scope against one release package.

Carlos L

Sobre o autor

Carlos L

Engenheiro de CAM e Manufatura de PCB na Highleap Electronics

Charles possui mais de 10 anos de experiência em engenharia CAM de PCBs e fabricação eletrônica, com especialização em verificação de arquivos de PCB, análise DFM e preparação para produção de placas multicamadas, HDI, RF e de alta velocidade. Proficiente em Genesis, InCAM e CAM350, ele garante dados precisos, processos estáveis ​​e alto rendimento de fabricação.

Na Highleap Electronics, ele se concentra na otimização de processos e na avaliação da viabilidade de fabricação para ajudar os clientes a reduzir riscos, diminuir prazos de entrega e alcançar resultados de produção confiáveis.

Soluções Highleap para PCBs e PCBA - solicite um orçamento

Posts recomendados

Como obter um orçamento para PCBs

Vamos realizar uma análise DFM/DFA para você e entraremos em contato com um relatório. Você pode enviar seus arquivos com segurança pelo nosso site. Precisamos das seguintes informações para lhe fornecer um orçamento:

    • Gerber, ODB++ ou .pcb, especificação.
    • Lista de materiais caso necessite de montagem
    • Qtd.
    • Hora de virar

Além da fabricação de PCBs, oferecemos uma gama completa de serviços eletrônicos, incluindo design de PCBs, PCBA e soluções completas. Seja para prototipagem, verificação de design, fornecimento de componentes ou produção em massa, oferecemos suporte completo para garantir o sucesso do seu projeto.

Para serviços de PCBA, forneça sua BOM (Lista de Materiais) e quaisquer instruções específicas de montagem. Também oferecemos análise DFM/DFA para otimizar seus projetos quanto à capacidade de fabricação e montagem, garantindo um processo de produção tranquilo.

    Conte-nos sobre o seu projeto de PCB.

    Ainda não tem arquivos de projeto? Sem problemas. Compartilhe o que você sabe e entraremos em contato caso precisemos de mais detalhes.



    Fazer upload de arquivos (Opcional)

    Arquivos de PCB, lista de materiais (BOM), PDF/STEP, TXT, imagens, ZIP/RAR/7Z · Máximo de 50 MB no total