Właściwości i zastosowania materiału PCB IT-258GA3

IT-258GA3 PCB banner with three green boards and exposed gold pads

Illustration of heavy-copper PCB panel layouts.

ITEQ IT-258GA3 is a halogen-free, medium-Tg laminate and prepreg system for rigid multilayer boards, including automotive ECUs and heavy-copper builds. Its datasheet lists 155°C Tg by DSC, a CTI of 400–599 V (class 1) and thermal conductivity of 0.70 W/m·K. These properties support three separate design checks: how the copper carries current, how the board maintains insulation and how the assembly removes heat.

Treat creepage, clearance and internal CAF as different paths

Comparative tracking index (CTI) describes how an insulating material behaves in a standardized contaminated-surface tracking test. CTI class 1 in the ITEQ sheet does not specify a safe board operating voltage. Determine creepage along exposed insulating surfaces from the governing product requirements and the applicable material group, working voltage and pollution degree. Determine clearance through air from the applicable voltage stresses, overvoltage and altitude considerations. Confirm any assumptions about coating, slots and barriers against the governing standard rather than assigning a universal spacing from the laminate name.

Conductive anodic filament (CAF) growth is a separate failure mechanism. Moisture can enter paths along the resin-to-glass interface; with electric bias and susceptible geometry, conductive growth can develop internally between conductors. Closely spaced plated holes or holes next to internal copper are important review points. Layout spacing, drill-induced damage, the construction and the moisture/bias environment all matter. Consult IEC 60664-1 for insulation coordination where it applies. It does not replace a product-specific qualification plan for buried conductor spacings.

ITEQ describes CAF resistance with a 1000 V claim in the sheet’s feature summary but does not publish the test spacing, humidity and duration there. For a product qualification, define the coupon’s conductor geometry, test bias and moisture exposure, observation period and insulation-resistance acceptance. A dry finished-board opens-and-shorts test does not answer that question. Conversely, a good humidity-bias result on a bare-board coupon does not qualify surface contamination or assembly residues on the populated product. When selecting a Materiał PCB odporny na CAF, decide which failure geometry the coupon must represent.

Specify the copper that remains after etch and plating

“4 oz copper” does not say whether the callout is starting foil or finished copper, which layers it covers, or how the narrowest current-carrying section is accepted. A power net may cross a wide plane, narrow through a connector or fuse footprint, then change layers through a plated-via array. The highest current density can occur at the neck or at the vias even when the plane itself has low resistance.

Hypothetical resistance check. A straight copper neck 20 mm long, 2.0 mm wide and 70 µm thick has an ideal room-temperature resistance of about 2.5 mΩ using 1.72 × 10-8 Ω·m for copper. At 10 A DC it dissipates about 0.25 W. If the effective width falls to 1.5 mm at the same thickness, the estimate rises to about 3.3 mΩ and 0.33 W. The simple rectangular model ignores taper, plated variations, vias and solder joints. It predicts resistive heating, not allowable current or temperature rise.

For production, state the finished copper requirement per layer, the critical conductor widths and spacings after etch, and the via-wall acceptance. On external layers, distinguish base foil from any plating contribution. In thick copper, lateral etching can narrow a trace and change sidewall shape; pattern plating can produce different thicknesses in sparse and dense areas. Review the finished section at a representative constriction and the plated transition, not only on a large test pad. IPC-2152 supplies a framework for current-carrying capacity. Apply an appropriate model or measurement for the actual copper paths, adjacent planes, ambient conditions and allowed rise.

IT-258GA3 PCBA illustration with a populated board and pin connector

PCBA illustration with a connector and populated board. Current paths and solder requirements depend on the design.

Review the lamination and thermal path together

Heavy inner copper creates cavities where adjacent copper was etched away. A thicker foil does not automatically mean a thicker finished dielectric above the trace; prepreg resin has to fill the cavities and keep adequate separation over the copper. Compare resin demand at dense copper, large cleared areas and isolation boundaries. Check the actual pressed spacing and resin fill on representative sections, especially at abrupt copper-density changes. A balanced heavy-copper stack-up should also be reviewed for panel flatness and the plating challenge at thick-board through holes.

Draw the heat path from each power device through its package attachment, copper spreading area, any thermal vias and the interface to the enclosure or heatsink. The laminate conductivity is just one part of that network. A thin dielectric over a useful spreading plane and a thick dielectric behind a small device can yield very different temperatures even with the same resin system. At first article, measure under representative current, enclosure and airflow conditions. Watch for connector necks and layer transitions as well as the power device itself.

WYKONANIE I MONTAŻ PCB

Planning an IT-258GA3 PCB build?

Highleap może wspólnie omówić wymagania dotyczące konstrukcji i montażu płyty.

Include finished copper requirements, insulation constraints and connector soldering details.

Poproś o przegląd produkcji i montażu

IT-258GA3TC is the laminate designation

In the current ITEQ sheet, IT-258GA3TC identifies the copper-clad laminate for the IT-258GA3 system; IT-258GA3BS identifies its prepreg. Use those designations to check the stack-up and purchasing description. The grade is a candidate for thick copper and insulation-sensitive rigid boards; the 10 GHz datasheet values also help screen whether a long high-speed route needs a separate material decision.

Selected IT-258GA3 material data
Właściwość ITEQ value Podstawa lub ograniczenie
Tg and MOT 155°C Tg; 130°C MOT DSC and UL 746, respectively
Wskaźnik śledzenia porównawczego Class 1 (400–599 V) ASTM D3638 / UL 746 as listed; test classification
Przewodność cieplna 0.70 W/m·K ITEQ feature summary; not a populated-board thermal resistance
Rozszerzenie osi Z 2.8% od 50°C do 260°C IPC-TM-650 2.4.24; próbka laminatu
Dk / Df przy 10 GHz 4.3 / 0.016 Zawartość żywicy 50%; IPC-TM-650 2.5.5.13

Źródło: ITEQ IT-258GA3 datasheet, Rev. 1.0-26.

Bring the connector and solder process into the release

Large copper planes can draw heat out of a soldered terminal while nearby SMT parts heat much faster. In heavy-copper PCB assembly, review thermal reliefs, solder fill and heat exposure with the mechanical and electrical constraints in view. An isolated thermal relief may make the joint easier to solder but can constrict the current path. If a connector instead uses press-fit pins or a bolted connection, coordinate the hole tolerances and insertion or clamping loads with the board stack and support.

Dla Highleap PCB and assembly quotation, identify the finished copper by layer, send the current waveform and allowable rise, and show the working-voltage and transient requirements with the insulation boundaries. Include plated-hole requirements, terminal drawings, the BOM and the needed evidence for first article. This lets Highleap Electronics review the copper geometry, press construction and assembly process against the same product requirements.

Ashley

O autorze

Ashley

Starszy menedżer ds. biznesu międzynarodowego w Highleap Electronics

Ashley specjalizuje się w kompleksowych rozwiązaniach PCB i PCBA, oferując klientom międzynarodowym wsparcie w zakresie analizy DFM, optymalizacji plików Gerber oraz koordynacji inżynieryjnej od produkcji PCB do produkcji EMS.

Dzięki doskonałym umiejętnościom komunikacji technicznej i biegłej znajomości języka angielskiego, ściśle współpracuje z zespołami inżynierskimi, aby dostosować założenia projektowe, procesy produkcyjne i wymagania jakościowe — pomagając zapewnić niezawodną realizację złożonych projektów PCB i PCBA.

Rozwiązania Highleap PCB i PCBA – zapytaj o wycenę

Polecamy Wiadomości

Jak uzyskać wycenę płytek PCB

Przeprowadzimy analizę DFM/DFA dla Ciebie i wrócimy do Ciebie z raportem. Możesz bezpiecznie przesłać swoje pliki za pośrednictwem naszej witryny. Wymagamy następujących informacji, aby przedstawić Ci wycenę:

    • Gerber, ODB++ lub .pcb, specyfikacja.
    • Lista BOM, jeśli wymagany jest montaż
    • Ilość
    • Czas na zmianę

Oprócz produkcji PCB oferujemy kompleksowy zakres usług elektronicznych, w tym projektowanie PCB, PCBA i rozwiązania pod klucz. Niezależnie od tego, czy potrzebujesz pomocy w prototypowaniu, weryfikacji projektu, pozyskiwaniu komponentów czy masowej produkcji, zapewniamy kompleksowe wsparcie, aby zagwarantować sukces Twojego projektu.

W przypadku usług PCBA prosimy o dostarczenie BOM (listy materiałów) i wszelkich szczegółowych instrukcji montażu. Oferujemy również analizę DFM/DFA w celu optymalizacji projektów pod kątem możliwości produkcji i montażu, zapewniając płynny proces produkcji.

    Opowiedz nam o swoim projekcie PCB

    Nie masz jeszcze plików projektowych? Żaden problem. Podziel się swoją wiedzą, a skontaktujemy się z Tobą, jeśli będą potrzebne dodatkowe informacje.



    przesyłać pliki (opcjonalne)

    Pliki PCB, BOM, PDF/STEP, TXT, obrazy, ZIP/RAR/7Z · Maks. 50 MB łącznie